Heliocentris Energy Manager 1.3 Instruction Manual Download Page 57

Page: 57 / 78

Operating

Energy Manager 1.3 - Instruction Manual

5.7

How to Copy Log Files to USB Flash Drive

The entire log file directory of the Energy Manager can directly be copied

to a USB flash drive.



USB flash drive with one partition only (FAT32 formated)

On the USB flash drive a file with a log identifier has to be created using

the Windows Editor or WordPad. The file name must not be

complemented by any extension (such as txt or csv).

TIP

Don’t use Microsoft Word, the format is not supported.

The log files are copied to the USB flash drive with the current date and

time. Each time the USB flash drive is plugged in, a new directory is

created and all files are copied again.
Prepare USB flash drive as follows:
1.

Insert USB flash drive into USB port of PC or laptop.

Open the Windows Editor or WordPad.

Create a new file.

Write identifier

P21getlog

into the file.

Save file under file name

Identifier

(capital “I”, without extention).

Remove USB flash drive from PC or laptop.

The copying process takes a few minutes. The copying process continues

until finishing. If the USB flash drive has not enough memory left a

message is shown at the display.
Copy log file to USB flash drive as follows:
1.

Plug USB flash drive into a USB port on the left side of Energy

Manager.



After a few seconds the status of the copy procedure is displayed

on the LCD.

Notice ! Damage to the data of the USB flash drive might result on
removing the drive during the running process. Don’t remove the USB

flash drive during the running process.



A message is displayed when the process is finished.

Remove USB flash drive.

Prepare USB flash drive

Copy log file to

USB flash drive

Summary of Contents for Energy Manager 1.3















































































Search results

Summary of Contents for Energy Manager 1.3

Reviews:

Related manuals for Energy Manager 1.3

Brands by name

Popular brands

Heliocentris Energy Manager 1.3, Instruction Manual

Search results

Summary of Contents for Energy Manager 1.3

Reviews:

Related manuals for Energy Manager 1.3

Brands by name

Popular brands