Heliocentris Energy Manager 1.3 Instruction Manual Download Page 34

Page: 34 / 78

Operating

Energy Manager 1.3 - Instruction Manual

Main menu

Description

Load

Load module. Status data of the power consumption

of the site can be accessed. Behind the item either
the load in kW or an event is displayed.

Solar

Solar module. Behind the item the power generation

in kW or an event is displayed.

Wind

Wind module. Behind the item the power generation
in kW or an event is displayed.

Airc

Aircondition module. Status data of air condition can
be accessed. Behind the item the operating mode or
an event is displayed.

FCU

Free Cooling Unit module. Status data of fan can be

accessed. Behind the item the operating mode or an
event is displayed.

Rect

Rectifier module. Behind the item the operating mode

or an event is displayed.

Invert

Inverter module. Behind the item the power in the 3
phases in kW or an event is displayed.

Site

Site module. Behind the item the outside temperature
and humidity or an event is displayed.

Shelter

Shelter module. Behind the item the inside

temperature and humidity or an event is displayed.

Service

Service contact and system informatioin for different
low level modules, reboot and power down

command can be accessed.

Configuration

A limited amount of configuration settings can be

accessed.

Table 5-1 Main menu

Summary of Contents for Energy Manager 1.3















































































Search results

Summary of Contents for Energy Manager 1.3

Reviews:

Related manuals for Energy Manager 1.3

Brands by name

Popular brands

Heliocentris Energy Manager 1.3, Instruction Manual

Search results

Summary of Contents for Energy Manager 1.3

Reviews:

Related manuals for Energy Manager 1.3

Brands by name

Popular brands