Heliocentris Energy Manager 1.3 Instruction Manual Download Page 37

Page: 37 / 78

Operating

Energy Manager 1.3 - Instruction Manual

Menu item

Display

Description

I/C

remote on

Genset unit was switched on

remotely. It will run as long as
the remote on mode is set.

StateRpl

One of the

replies:

State reply. System answer on a

user command (CMD).

run

User requested online mode.
Genset unit will switch to 1 of the
following operating modes:

Standby

Active

Error

Manual

offline

User requested offline mode.

Genset unit will switch to offline
operating mode.

monitor

User requested monitoring mode.

Genset unit will switch to 1 of the
following operating modes:

Monitor

Active

Error

remote on

User requested remote on mode.

Genset unit will switch to 1 of the
following operating modes:

Remote on

Error

test

User requested test mode.

CMD

One of the
commands:

Commands to be entered by a
service user.

go online

Request for online/run state. Unit

will switch to 1 of the online
operating modes. Can only be
executed in offline or remote on
operating mode.

go offline

Request for offline state. Unit will

switch to offline operating mode.
Can be executed in any operating
mode.

go testmode

Request for test mode state. Unit

will switch to test mode. Can only
be executed in offline mode.

go monitor

Request for monitor mode. Unit

will switch to 1 of the monitor
operating modes once the
command was successful. Can
only be executed in offline or
Remote on operating mode.

cancel cmd

Cancel a pending state request.

Summary of Contents for Energy Manager 1.3















































































Search results

Summary of Contents for Energy Manager 1.3

Reviews:

Related manuals for Energy Manager 1.3

Brands by name

Popular brands

Heliocentris Energy Manager 1.3, Instruction Manual

Search results

Summary of Contents for Energy Manager 1.3

Reviews:

Related manuals for Energy Manager 1.3

Brands by name

Popular brands