HEIDENHAIN TNC 370 D Technical Information Download Page 73

Page: 73 / 92

4–70

TNC 370 D

Machine Parameters

July 02

4.12 Tapping

Machine
parameter

Function and input

Change via

Reaction

MP7110.0

Minimum for feed-rate override during
tapping
Input:

0 to 150 [%]

PLC
RUN

MP7110.1

Maximum for feed-rate override during
tapping
Input:

0 to 150 [%]

PLC
RUN

MP7120.0

Dwell time for reversal of spindle rotation
direction
Input:

0 to 65.535 [s]

PLC
RUN

MP7120.1

Advanced switching time of the spindle for
tapping with coded output of the spindle
speed
Input:

0 to 65.535 [s]

PLC
RUN

MP7120.2

Spindle slow-down time after reaching the
total hole depth
Input:

0 to 65.535 [s]

PLC
RUN

MP7130

Approach behavior of the spindle for rigid
tapping
Input:

0.01 to 10.000 [°/min]

PLC

MP7150

Positioning window of the tool axis for rigid
tapping
Input:

0.001 to 2.000 [mm]

PLC

MP7160

Spindle orientation with Cycle 17
Input:
0= spindle orientation before execution of

Cycle 17

1= no spindle orientation before execution

of Cycle 17

CN
PLC
RUN

Summary of Contents for TNC 370 D





























































































Search results

Summary of Contents for TNC 370 D

Reviews:

Related manuals for TNC 370 D

Brands by name

Popular brands

HEIDENHAIN TNC 370 D, Technical Information

Search results

Summary of Contents for TNC 370 D

Reviews:

Related manuals for TNC 370 D

Brands by name

Popular brands