HEIDENHAIN TNC 370 D Technical Information Download Page 75

Page: 75 / 92

4–72

TNC 370 D

Machine Parameters

July 02

Machine
parameter

Function and input

Change via

Reaction

MP7260

Number of the tools in the tool table
Input:

0 to 254

MP7261

Number of pockets in the tool magazine
Input:

0 to 254

MP7266

MP7266.0
MP7266.1
MP7266.2
MP7266.3
MP7266.4
MP7266.5
MP7266.6
MP7266.7
MP7266.8
MP7266.9
MP7266.10
MP7266.11
MP7266.12
MP7266.13
MP7266.14
MP7266.15
MP7266.16
MP7266.17
MP7266.18
MP7266.19
MP7266.20

MP7266.21

Elements of the tool table
Input:
0 = no display
1 to 99 = position in the tool table
Tool name

(NAME)

Tool length

(L)

Tool radius (R)

Free

Oversize for tool length

(DL)

Oversize for tool radius

(DR)

Free

Tool locked?

(TL)

Replacement tool

(RT)

TIME 1
TIME 2
CURRENT TIME
Comment about the tool

(DOC)

Number of tool teeth

(CUT)

Wear tolerance for tool length (LTOL)
Wear tolerance for tool radius (RTOL)
Cutting direction of the tool

(DIRECT)

PLC status (PLC)
Tool offset for length

(TT: L-OFFS)

Tool offset for radius

(TT: R-OFFS)

Breakage tolerance for tool length

(LBREAK)

Breakage tolerance for tool radius

(RBREAK)

MP7267

MP7267.0
MP7267.1
MP7267.2
MP7267.3
MP7267.4

Elements of the pocket table
Input:
0 = no display
1 to 99 = position in the pocket table
Tool number

(T)

Special tool

(ST)

Fixed pocket

(F)

Locked pocket

(L)

PLC status (PLC)

Summary of Contents for TNC 370 D





























































































Search results

Summary of Contents for TNC 370 D

Reviews:

Related manuals for TNC 370 D

Brands by name

Popular brands

HEIDENHAIN TNC 370 D, Technical Information

Search results

Summary of Contents for TNC 370 D

Reviews:

Related manuals for TNC 370 D

Brands by name

Popular brands