HEIDENHAIN TNC 370 D Technical Information Download Page 89

Page: 89 / 92

5–86

TNC 370 D

List of Markers and Words

July 02

Word Function

W320

Nominal rotational speed (only with controlled spindle)

W322

Actual rotational speed (only with controlled spindle)

D356

Programmed rotational speed

D360

Programmed feed rate

(NC

PLC)

D388

Current feed rate

W392

Analog voltage on connector X8

W480

Voltage input 0

on the LE

W482

Voltage input 1

on the LE

W484

Voltage input 2

on the LE

W486

Temperature input 0

on the LE

W488

Temperature input 1

on the LE

W492

Percentage factor for spindle override

(NC

PLC)

W494

Percentage factor for feed-rate override (NC

PLC)

W516

Number of the Q parameter to be overwritten (Q100 to Q107 = 0 to 7)

W522

Switch off the monitoring functions if the PLC input from MP4130 is
activated

D528

Value to be transferred to the Q parameters
Datum shift for X axis
Position axis X [1/10 000 mm]

D532

Datum shift for Y axis
Position of axis Y

D536

Datum shift for Z axis
Position of axis Z

D540

Datum shift for IV axis
Position of axis 4

W560

Feed rate in axis X [mm/min]

W562

Feed rate in axis Y

W564

Feed rate in axis Z

W566

Feed rate in axis 4

W576
W578
W580
W582

Lag-tracking error compensation (compensation speed from MP4070)
Input range: + 32 767 to – 32 768 [1/10 000mm]
Axis X
Axis Y
Axis Z
Axis 4

Summary of Contents for TNC 370 D





























































































Search results

Summary of Contents for TNC 370 D

Reviews:

Related manuals for TNC 370 D

Brands by name

Popular brands

HEIDENHAIN TNC 370 D, Technical Information

Search results

Summary of Contents for TNC 370 D

Reviews:

Related manuals for TNC 370 D

Brands by name

Popular brands