Heat & Glo REVO-H31 Installation Manual Download Page 12

Page: 12 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

B. Clearance to Combustibles

When selecting a location for the appliance it is important

to consider the required clearances to walls (see Figure

3.6).

WARNING! Risk of Fire or Burns!

Provide adequate

clearance around air openings and for service access.

Due to high temperatures, the appliance should be lo-

cated out of traffic and away from furniture and draperies.

NOTICE:

Illustrations reflect typical installations and are

FOR DESIGN PURPOSES ONLY. Illustrations/diagrams

are not drawn to scale. Actual installation may vary due to

individual design preference.

Figure 3.6 Appliance Locations

WARNING! Risk of Fire!

Maintain specified air space

clearances to appliance and vent pipe:

• Insulation and other materials must be secured to prevent

accidental contact.

• The chase must be properly blocked to prevent blown

insulation or other combustibles from entering and

making contact with fireplace or chimney.

• Failure to maintain airspace may cause overheating and

a fire.

See Figure 3.6, 3.7, 3.8, 3.9, and 3.11 for framing

dimension requirements and required clearances.

41 IN.

(1041 mm)

20-1/8 IN.

(511 mm)

50-13/16 IN.

(1291 mm)

27-1/16 IN.

(687 mm)

37-1/16 IN.

(941 mm)

17-5/16 IN.

(440 mm)

34-5/16 IN.

(872 mm)

15-3/8 IN.

(391 mm)

REVO-H31

REVO-V12

REVO-S21

REVO-H31

REVO-S21

1 IN. MINIMUM

(25 mm)

ZERO CLEARANCE

Refer to Sections 10.D and 10.E for

mantel and wall projection information.

12 IN.

(305 mm)

12 IN.

(305 mm)

1 IN. MINIMUM

(25 mm)

Note:

The REVO-V12 is the only REVO appliance that can be vented with a 45 degree elbow directly off the

back positioned horizontally. See Section 4.F.

Summary of Contents for REVO-H31






































































Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands

Heat & Glo REVO-H31, Installation Manual

Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands