Heat & Glo REVO-H31 Installation Manual Download Page 41

Page: 41 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

Important Notice:

Heat shields may not

be field constructed.

F. Horizontal Termination Requirements

Heat Shield Requirements for Horizontal

Termination

WARNING! Risk of Fire!

To prevent overheating and

fire, heat shields must extend through the entire wall

thickness.

•

DO NOT

remove the heat shields attached to the

wall shield firestop and the horizontal termination cap

(shown in Figure 7.13).

• Heat shields must overlap 1-1/2 in. (38 mm) mini

mum.

There are two sections of the heat shield. One section

is factory-attached to the wall shield firestop. The other

section is factory-attached to the cap. See Figure 7.13.

If the wall thickness does not allow the required 1-1/2 in.

(38 mm) heat shield overlap when installed, an extended

heat shield must be used.

• If the wall thickness is less than 4-3/8 in./ 111 mm

(SLP), the heat shields on the cap and wall shield

firestop must be trimmed. A minimum 1-1/2 in. (38 mm)

overlap MUST be maintained.

• Use an extended heat shield if the finished wall

thickness is greater than 7-1/4 in. (184 mm).

• The extended heat shield may need to be cut to length

maintaining sufficient length for a 1-1/2 in. (38 mm)

overlap between heat shields.

• Attach the extended heat shield to either of the

existing heat shields using the screws supplied with

the extended heat shield. Refer to vent components

diagrams in the back of this manual.

• Rest the small leg on the extended heat shield on top

of the pipe section to properly space it from the pipe

section.

Figure 7.13 Venting through the wall

Note:

When using termination caps with factory-supplied

heat shield attached, no additional wall shield firestop is

required on the exterior side of a combustible wall.

Install Horizontal Termination Cap

WARNING! Risk of Fire!

The telescoping flue section of

the termination cap MUST be used when connecting vent.

• 1-1/2 (38 mm) minimum overlap of flue telescoping

section is required.

Failure to maintain overlap may cause overheating and

fire.

• Vent termination must not be recessed in the wall. Siding

may be brought to the edge of the cap base.

• Flash and seal as appropriate for siding material at

outside edges of cap.

• When installing a horizontal termination cap, follow

the cap location guidelines as prescribed by current

ANSI Z223.1

and

CAN/CGA-B149

installation codes

and refer to Section 4 of this manual.

CAUTION! Risk of Burns!

Local codes may require in-

stallation of a cap shield to prevent anything or anyone

from touching the hot cap.

NOTICE:

For certain exposures which require superior

resistance to wind-driven rain penetration, a flashing kit and

HRC caps are available. When penetrating a brick wall, a

brick extension kit is available for framing the brick.

INTERIOR

HEAT SHIELD OR

EXTENDED

HEAT SHIELD

WALL SHIELD

FIRESTOP

HEAT SHIELD

1-1/2 IN. (38 MM) MIN.

OVERLAP

SHEATHING

VENT DEPTH FROM BACK

OF APPLIANCE OUTER WRAP

TO OUTSIDE SURFACE

OF EXTERIOR WALL

(SEE CHART BELOW)

SLIP SECTION

CAN BE EXTENDED

EXTERIOR

WALL

OUTER WRAP

Termination Cap Specification Chart

(Depth without using additional pipe sections)

SLP-TRAP1 can adjust 2-3/8 in. (4-1/8 in. to 6-1/2 in.)
SLP-TRAP2 can adjust 4-1/2 in. (6-1/2 in. to 11 in)

Summary of Contents for REVO-H31






































































Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands

Heat & Glo REVO-H31, Installation Manual

Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands