Heat & Glo REVO-H31 Installation Manual Download Page 27

Page: 27 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

A. Pipe Clearances to Combustibles

WARNING! Risk of Fire!

Maintain air space clearance to

vent.

DO NOT

pack insulation or other combustibles:

• Between ceiling firestops

• Between wall shield firestops

• Around vent system

Failure to keep insulation or other material away from

vent pipe may cause overheating and fire.

Vent Clearances and Framing

Figure 5.2 Wall Penetration

Figure 5.1 Horizontal Venting Clearances To Combustible

Materials

B. Wall Penetration Framing/Firestops

Combustible wall Penetration

Whenever a combustible wall is penetrated, you must

frame a hole for the wall shield firestop(s). The wall shield

firestop maintains minimum clearances and prevents cold

air infiltration.
• The opening must be framed on all four sides using the

same size framing materials as those used in the wall

construction.

* When using SLP pipe, minimum clearances from the vent pipe to combustible

materials at inside wall firestops are:

Top: 2-1/2 in. (64 mm)

Bottom: 1/2 in. (13 mm)

Sides: 1 in. (25 mm)

Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm).

•

SLP heat shield

- designed to be used on a wall 4-3/8 in. to 7-5/8 in. (111 mm to

194 mm thick).

• If wall thickness is less than 4-3/8 the existing heat shields must be field trimmed.

If wall thickness is greater than 7-5/8 in. a DVP-HSM-B will be required.

(SLP Pipe Shown)

3 in. (76 mm)

top clearance *

1 in. (25 mm)

clearance

bottom & sides

Heat

Shield

Wall

Shield

Firestop

Heat

Shield

WALL

10-3/16 iN.

12 IN.

DO NOT PACK WITH

INSULATION OR

OTHER MATERIAL

FINISHED

FLOOR

Revo-V12

in.

= 4 in.min.

(102 mm)

28-1/2

C=(A + B) +1 in.

(1 in. =25 mm)

724

Revo-S21

in.

660

Revo-H31

in.

21-1/2

546

WARNING! Risk of overheating!

Install appliance a

minimum of 4 inches off of finished floor.
• Convection air flow could be compromised and

cause overheating.

• Decorative fronts will not fit properly.

* Shows center of vent framing hole for venting. The center

of the hole is one (1) inch (25.4 mm) above the center of

the horizontal vent pipe.

• SLP pipe - A wall shield firestop must be placed on each

side of an interior wall. A minimum 1-1/2 in. (38 mm)

overlap of attached heat shields must be maintained.

• See Section 7.F. for information for regarding the instal

lation of a horizontal termination cap.

Non-Combustible Wall Penetration

If the hole being penetrated is surrounded by non-com-

bustible materials such as concrete, a hole with diameter

one inch greater than the pipe is acceptable.
Whenever a non-combustible wall is penetrated, the wall

shield firestop is only required on one side and no heat

shield is necessary.

Note:

Vertical venting requires 1 inch clearance on all

sides of the pipe.

Summary of Contents for REVO-H31






































































Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands

Heat & Glo REVO-H31, Installation Manual

Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands