Heat & Glo REVO-H31 Installation Manual Download Page 66

Page: 66 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

Optional wire Harness

DESCRIPTION

PART NUMBER

10 FT PV Wire Harness

PVI-WH10

20 FT PV Wire Harness

PVI-WH20

40 FT PV Wire Harness

PVI-WH40

60 FT PV Wire Harness

PVI-WH60

80 FT PV Wire Harness

PVI-WH80

100 FT PV Wire Harness

PVI-WH100

PVI-SLP

Power Vent Inline

Note:

Wire harnesses required to power the PVI-SLP

connect to the appliance and are ordered separately from

PVI-SLP. Contact your dealer to order.

12-1/2 IN.

318 mm

20-3/4 IN.

527 mm

13-5/8 IN.

346 mm

EFFECTIVE LENGTH

32 IN. (813 mm) MIN.

35 IN. (889 mm) MAX.

A. Vent Components Diagrams (

continued

)

PVK-80

(Not approved for use with REVO-V12.)

11-1/2 in.

(292 mm)

12-1/2 in.

(318 mm)

16 in.

(406 mm)

9 in.

(229 mm)

2-3/4 in.

(70 mm)

12-1/4 in.

(311 mm)

Note:

Vent runs including the PVK-80 or

PVI-SLP may not exceed 30 feet in total

vent length or six 90 degree elbows.

Figure 13.4 SLP vent components

Note:

Use only approved termination caps with the PVI-

SLP. See instructions included with PVI-SLP kit.

Summary of Contents for REVO-H31






































































Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands

Heat & Glo REVO-H31, Installation Manual

Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands