Heat & Glo REVO-H31 Installation Manual Download Page 33

Page: 33 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

Figure 6.9 Install Appliance Outer Wrap

FRAMING

F SHEETROCK

+ APPLIANCE OUTER WRAP

F SHEETROCK

MATERIAL CAN BE

COMBUSTIBLE

I.E. SHEETROCK

F SHEETROCK

+ APPLIANCE OUTER WRAP + HOLE CUT

CUT OUT MATERIAL

FOR VENT

APPLIANCE

OUTER WRAP

APPLIANCE

OUTER WRAP

REMOVE CORRUGATED TEMPLATE PRIOR TO INSTALLING SHEET ROCK

OR PRIOR TO INSTALLING APPLIANCE OUTER WRAP

C. Install Appliance Outer Wrap (On-Wall

Installation)

1. Remove the glass assembly from the firebox by releas

ing the two top glass latches and then the two bottom

glass latches. See Figure 12.1.

2. Remove the screws that attach the firebox to the outer

wrap. See Figure 6.8. Separate the firebox from the

outer wrap. Carefully set the firebox aside holding it by

the sides. Do not grab, lift or carry the appliance by the

top heat shield, or component tray. Lay the appliance

on its back to avoid damaging the component tray.

Note:

Do not remove outer heat shields.

3. Position the outer wrap on the wall and ensure it is

level. See Figure 6.9. A minimum of two screws must

be attached to the vertical wall studs. Secure with the

fasteners provided. See Figure 6.11(C) and Figure

6.12.

CAUTION!

Outer wrap and appliance MUST be in

stalled level for proper burner operation.

DO NOT REMOVE SCREW

(BOTH SIDES)

NOTE: The REVO-V12 has 4 screws

on each side of the firebox.

FIREBOX

COMPONENT TRAY

(DO NOT GRAB)

APPLIANCE TOP HEAT SHIELD

(DO NOT GRAB)

OUTER HEAT SHIELDS

DO NOT REMOVE

APPLIANCE

OUTER WRAP

Figure 6.8

Remove Firebox from Outer Wrap

4. Cut hole through wall as indicated in Figure 6.9. You

may use the appliance outer wrap as a guide.

WARNING! Risk of Fire!

Prevent contact with:

•  Sagging or loose insulation
•  Insulation backing or plastic
•  Framing and other combustible materials

Block openings into the chase to prevent entry of blown-in

insulation. Make sure insulation and other materials are

secured.

Failure to maintain air space clearance may cause over-

heating and fire.

5. Frame around the edges of the firestop cut out to ensure

insulation does not come into contact with the vent pipe.

See Figure 6.10 and 6.12.

6. Install wall firestop with four screws. See Figure 6.10

and Figure 6.11(C).

7. Seal the wall firestop. See Section 6.A.

Summary of Contents for REVO-H31






































































Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands

Heat & Glo REVO-H31, Installation Manual

Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands