Heat & Glo REVO-H31 Installation Manual Download Page 43

Page: 43 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

B. Wiring Requirements

IntelliFire™ Plus

Ignition System Wiring

NOTICE:

Batteries should only be used as a power source

in the event of an emergency power outage. Batteries

should not be used as a primary long-term power source.

Battery polarity must be correct when installing batteries.

Do not store batteries in the battery pack when the

appliance is powered by the 6 volt transformer connected

to permanent electrical service.

• Wire the appliance junction box to 110-120 VAC for

proper operation of the appliance.

WARNING! Risk of Shock or Explosion! DO NOT

wire

IPI controlled appliance junction box to a switched circuit.

Incorrect wiring will override IPI safety lockout.

• Refer to Figure 8.2, IPI Wiring Diagram.
• This appliance is equipped with an IntelliFire™ Plus

control valve which operates on a 6 volt/1.5 AMP system.

Figure 8.2

IntelliFire™ Plus

Ignition (IPI) Wiring Diagram

TO JUNCTION

BOX (110V)

MODULE

FLAME

SENSE

IGNITER

GROUND

ORANGE

(PILOT)

GREEN

(MAIN)

BROWN

BLACK

RED

FLAME

MODULATION

RC200

BATTERY PACK

6V DC

• Plug the 6 volt transformer plug into the appliance junction

box to supply power to the unit OR install 4 AA cell

batteries (not included) into the battery pack before use.

Summary of Contents for REVO-H31






































































Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands

Heat & Glo REVO-H31, Installation Manual

Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands