Heat & Glo REVO-H31 Installation Manual Download Page 4

Page: 4 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

B. Glass Specifications

This appliance is equipped with 5 mm ceramic glass. Re-

place glass only with 5 mm ceramic glass. Please contact

your dealer for replacement glass.

C. BTU Specifications

A. Appliance Certification

E. Non-Combustible Materials Specification

Material which will not ignite and burn. Such materials are

those consisting entirely of steel, iron, brick, tile, concrete,

slate, glass or plasters, or any combination thereof.

Materials that are reported as passing

ASTM E 136,

Standard Test Method for Behavior of Materials in

a Vertical Tube Furnace at 750 ºC

shall be considered

non-combustible materials.

F. Combustible Materials Specification

Materials made of or surfaced with wood, compressed pa-

per, plant fibers, plastics, or other material that can ignite

and burn, whether flame proofed or not, or plastered or

unplastered shall be considered combustible materials.

G. Electrical Codes

NOTICE:

This appliance must be electrically wired

and grounded in accordance with local codes or, in the

absence of local codes, with

National Electric Code

ANSI/NFPA 70-latest edition

or the

Canadian Electric

Code CSA C22.1.

• A 110-120 VAC circuit for this product must be pro

tected with ground-fault circuit-interrupter protection,

in compliance with the applicable electrical codes,

when it is installed in locations such as in bathrooms

or near sinks.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemen-

tal room heat or as a decorative appliance. It should not be

factored as primary heat in residential heating calculations.

D. High Altitude Installations

NOTICE:

If the heating value of the gas has been reduced,

these rules do not apply. Check with your local gas utility

or authorities having jurisdiction.

When installing above 2000 feet elevation:

• In the USA: Reduce input rate 4% for each 1000 feet

above 2000 feet.

• In CANADA: Input ratings are certified without a reduction

of input rate for elevations up to 4500 feet (1370 m)

above sea level. Please consult provincial and/or

local authorities having jurisdiction for installations at

elevations above 4500 feet (1370 m).

Check with your local gas utility to determine proper

orifice size.

NOTICE:

This installation must conform with local codes.

In the absence of local codes you must comply with the

National Fuel Gas Code, ANSI Z223.1-latest edition in

the U.S.A. and the CAN/CGA B149 Installation Codes in

Canada.

Product Specific and Important Safety Information

Models

(U.S. or Canada)

Maximum

Input BTU/h

Minimum

Input

BTU/h

Orifice

Size (DMS)

Revo-V12

(NG)

(0-2000 FT)

14,250

8,200

#50

Revo-V12

(LP)

(0-2000 FT)

13,350

8,500

#58

Revo-S21

(NG)

(0-2000 FT)

18,800

10,900

.083 in.

Revo-S21

(LP)

(0-2000 FT)

18,950

10,800

1.25 mm

Revo-H31

(NG)

(0-2000 FT)

24,000

12,700

#42

Revo-H31

(LP)

(0-2000 FT)

20,000

10,850

0.053 in.

MODELS:

Revo-V12, Revo-S21, Revo-H31

LABORATORY:

Underwriters Laboratories, Inc. (UL)

TYPE:

Direct Vent Heater

STANDARD:

ANSI Z21.88-2014/CSA 2.33-2014

This product is listed to ANSI standards fo “Vented Gas

Fireplace Heaters” and applicable sections of “Gas Burn-

ing Heating Appliances for Manufactured Homes and

Recreational Vehicles”, and “Gas Fired Appliances for

Use at High Altitudes”.

Summary of Contents for REVO-H31






































































Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands

Heat & Glo REVO-H31, Installation Manual

Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands