Heat & Glo REVO-H31 Installation Manual Download Page 46

Page: 46 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

Finishing (On-Wall Installation)

A. Facing and Finishing - Studio and Frame

Decorative Fronts

• Facing and/or finishing materials must not interfere

with convection vents, operation of doors, or access

for service. See Figure 10.1 and Figure 10.3.

• Observe all clearances when applying combustible

materials.

• Remove and discard finishing strip before installing

decorative front. See Figure 10.2.

• Use finishing strip to achieve required clearance. See

Figure 10.2 and 10.3.

WARNING! Risk of Fire! DO NOT

apply combustible

materials beyond the minimum clearances. Comply with

all minimum clearances to combustibles as specified in

this manual. Overlapping materials could ignite and will

interfere with proper operation of doors.

Figure 10.1 Convection Vent Location

WARNING!

Risk of Overheating and Fire!

Do not allow

convection air vents to be blocked or covered. Non-com-

bustible material must not exceed 4 inches in thickness.

DO NOT BLOCK CONVECTION VENTS

WITH FINISHING MATERIAL

REMOVE CLIPS

FINISHING STRIP

Figure 10.2 Remove Finishing Strip After Installation of Finishing

Material



Summary of Contents for REVO-H31






































































Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands

Heat & Glo REVO-H31, Installation Manual

Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands