Heat & Glo REVO-H31 Installation Manual Download Page 3

Page: 3 / 69

Heat & Glo • REVO-V12, REVO-S21, REVO-H31 Installation Manual • 2273-980 Rev. J • 5/15

Installation Standard work Checklist

Customer:

Lot/Address:

Model (circle one): REVO-V12

REVO-H31

REVO-S21

Date Installed:

Location of Fireplace:

Installer:

Dealer/Distributor Phone #

Serial #:

Comments:

Further description of the issues, who is responsible (Installer/ Builder/ Other Trades, etc) and corrective

action needed _____________________________________________________________________________________

_________________________________________________________________________________________________

Comments Communicated to party responsible ____________________ by ______________________on ___________

(Builder / Gen. Contractor/) (Installer) (Date)

Appliance Install

YES

IF NO, WHY?

Veri



ed that the area behind appliance is insulated and sealed as required. (Pg. 12)

___________________________

Required non-combustible board installed.(In-Wall Installation only) (Section 11)

___________________________

Veri



ed clearances to combustibles. (Section 3)

___________________________

Required In-Wall Kit installed if back of appliance outer wrap penetrates

the sheetrock/



nish wall material (In-Wall Installation only) ___________________________

Verified appliance is installed a minimum of 4 inches above finished floor. (Pg. 13,14,51) ___________________________

Veri



replace is leveled and secured. (Pg. 33,54)

___________________________

Venting/Chimney Section 7 (Pg 36-41)

Venting con



guration complies with allowable vent requirements.

___________________________

Venting installed, locked and secured in place with proper clearances.

___________________________

Interior/Exterior



restops installed and sealed (In-Wall Installation only).

___________________________

Attic insulation shield installed. (Pg 28)

___________________________

Terminations/Roof



ashing installed and sealed.

___________________________

Termination cap extension installed and sealed (In-Wall Installation only)(Section 11)

___________________________

Electrical Section 8 (Pg 42-43)

120VAC unswitched power provided to the appliance.

___________________________

Veri



ed ON/OFF switch wires properly installed.

___________________________

Gas Section 9 (Pg 44-45)

Appliance con



guration matches fuel type.

___________________________

Was a conversion performed?

___________________________

Leak check performed and inlet/outlet pressure veri



ed.

___________________________

Set air shutter for optimal



ame appearance.

___________________________

Finishing Section 10 (Pg 46-50)

Combustible materials not

installed in non-combustible areas.

___________________________

Veri



ed all clearances meet installation manual requirements.

___________________________

Mantels and wall projections comply with installation manual requirements.

___________________________

Appliance Setup Section 12 (Pg 59)

All packaging and protective materials are removed from inside/under /on

the appliance.

___________________________

Glass assembly installed and secured, glass retainers removed,gasket sealed.

___________________________

Accessories installed properly.

___________________________

Mesh, doors, or decorative front properly installed.

___________________________

Manual bag and all of its contents are removed from inside/under

the appliance and given to party responsible for use and operation.

___________________________

Operated appliance. Veri



ed no

gas leaks exist and proper appliance operation.

___________________________

2273-982E 9/14



= Contains updated information.

Hearth & Home Technologies recommends the following:

• Photographing the installation and copying this checklist for your



le.

• This checklist remain visible at all times on the appliance until the installation is complete.

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this

installation manual.

WARNING! Risk of Fire or Explosion!

Failure to install appliance according to these instructions can

lead to a



re or explosion.

ATTENTION INSTALLER:

Follow this Standard Work Checklist

Summary of Contents for REVO-H31






































































Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands

Heat & Glo REVO-H31, Installation Manual

Search results

Summary of Contents for REVO-H31

Reviews:

Related manuals for REVO-H31

Brands by name

Popular brands