manualshive.com logo in svg

hager HZI855, Instruction Manual, Page: 55 / 65

Share
Download
hager HZI855 Instruction Manual Download Page 55

6LE007317A

55

PRI

CHANGE PRIO

Changes the priority between sources

SS1

BYPASS STAB S1

Bypasses the stabilisation timer for S1

SS2

BYPASS STAB S2

Bypasses the stabilisation timer for S2

ALE

EXT ALARM

External alarm active. It will be logged in the alarm log as External Alarm and the Alarm LED will be active. The 

alarm will be In progress until input is cleared

FTE

EXT FAULT

External fault active. The product will transfer to position 0 / center off. CTRL is permitted. Mode will be inhibit. 

Genset will not start if source is lost. "EXTERNAL FAULT" will be displayed on screen. It will be logged in the fault 

log as External Fault and the Fault LED will be active. The fault will be In progress until input is cleared and fault 

reset.

MSR

PRIO TEST ON LOAD

EJP / Stay on "backup" source. Priority Test on Load. Order to stay in S2 even if the source is lost or 

unavailable.

OA1

FORCE S1 AVAIL.

Force Source 1 as Available

OA2

FORCE S2 AVAIL.

Force Source 2 as Available

OU1

FORCE S1 UNAVAIL.

Force Source 1 as Unavailable

OU2

FORCE S2 UNAVAIL.

Force Source 2 as Unavailable

RST

RST FAULT STATE

Fault Reset:

This input may be used to reset a fault condition after the fault has been cleared. Faults may also be reset 

through communication or through the display.

CHP

CHANGE PRIO

Changes the position (if no priority defined). It partially inhibits when active. It goes back to Auto when cleared. 

It has to be a permanent maintained input, it can't be an impulse.

Summary of Contents for HZI855


































































Reviews:

No comments