manualshive.com logo in svg

hager HZI855, Instruction Manual, Page: 22 / 65

Share
Download
hager HZI855 Instruction Manual Download Page 22

6LE007317A

22

10. Operation and control

10.1. HMI use

On the front face of the controller there are 14 keys/buttons that are used to configure, operate and visualize the ATS values anytime. 
Summary of the HMI buttons:

Button

Operation

Manual

Turns on CTRL mode. Allows the use of the I, 0, II buttons that will send position orders to the switch.

Automatic

Turns on AUTO mode. Controller will automatically perform transfers in case of priority source unavailability and priority source 

comeback.

I

Position I (source 1) manual order. Only in CTRL mode.

0

Position 0 (center-off) manual order. Only in CTRL mode.

II

Position II (source 2) manual order. Only in CTRL mode.

TEST

Performs a TEST (as defined inside Parameters/Display/Options menu)

Arrows

Navigation through different screens, menus, options and values.

Lamp Test/Fault clear

Press: lamp test and information about LED on screen

Long press: Clear faults pop-up (only if faults active)

Back/Menu

Press: back/return to previous screen or clear pop-up

Long press: Back to Main Menu page

Dashboard

Change between dashboard type (1 to 7, in a loop)

OK/Save & Quit

Press: Enter / OK / set a value / accept / confirm

Long press: (only when configuring) Save and Quit (back to previous configuration screen) 

1 

Manual operation buttons and indicator.

2 

Test button and indicator.

3 

Automatic button and LED indicator.

4 

Lamp test button.

5 

Power, Fault and alarm LED.

6 

Navigation buttons.

7 

Change dashboard.

8 

LCD display. 

9 

LED COM & Inhibit.

A 

Source and switch synoptic.

Summary of Contents for HZI855


































































Reviews:

No comments