manualshive.com logo in svg

hager HZI855, Instruction Manual, Page: 26 / 65

Share
Download
hager HZI855 Instruction Manual Download Page 26

6LE007317A

26

10.5. Test operating mode

TEST button on the HMI can be used (by default) to perform a TEST ON LOAD (as standard) or TEST OFF LOAD and can be configured 

inside the PARAMETERS/DISPLAY/OPTIONS menu (TEST BUTTON USE).
TEST ON LOAD Main-Gen: a test on load sequence will start by sending a start-gen signal to the secondary source (if in MAIN - GEN) , 

and will initiate a transfer to the the secondary source, once the test has ended the switch will transfer back to the priority source. 
TEST OFF LOAD will initiate starting of the genset but will not give the order to transfer to the secondary source when it becomes 

available.
The duration of the tests can be limited (in the configuration) or can be set to Unlimited, when set to unlimited the user will have to press 

the test button again to stop the tests.
This operation can also be performed with an input, using the EXT TEST ON LOAD function.

NOTE: TEST ON LOAD will cause a load supply 

interruption when testing the transfer function as the 

load will change from one source to another in open 

transition.

10.6. Control Menu

There are 3 type of commands available in the control menu and all of them require the operator profile password. Those commands are:

HZI855

MODE / POSITION:

 permits changing the operating mode, change position in CTRL mode and start/stop the gensets remotely (also in 

CTRL mode)

MODES:

•  AUTOMATIC: Standard automatic functioning of the controller
•  MANUAL / CTRL: Control of the switch manually using the controller to give orders to the switch. Buttons I-0-II are unblocked on the 

front face.

•  INHIBIT: Both CTRL and AUTO functions are inhibited until the mode changes. Message on the main dashboards (1.1 and 2.1) and 

buttons I-0-II, AUTO and CTRL will disable this mode but no remote orders will be taken into account.

NOTE: For a total inhibition, the inhibition inputs have to be used.

HZI855

CHANGE POSITION:

  (only in CTRL mode) permits sending orders to go to position 1, 0 (center-off) or 2 to the switch device.

GENSET SOURCE 1/2:

 permits START or STOP the gensets installed as source 1 or 2.

NOTE: The CONTROL/MODE menu is an “order” menu, 

to activate commands, but it doesn’t show the current 

mode or position (to visualize that the user needs to go 

to the dashboard screens).

Example: mode can be inhibited, but when entering 

the menu the mode will say “automatic” (which is not 

the current mode, it’s just a list of possible orders to 

be used.

Summary of Contents for HZI855


































































Reviews:

No comments