manualshive.com logo in svg

hager HZI855, Instruction Manual, Page: 14 / 65

Share
Download
hager HZI855 Instruction Manual Download Page 14

6LE007317A

14

All inputs and outputs can be configured and functions can be changed by going in the Parameters / I/O menu of the controller. 

For the cabling, please consider the following table of functioning:

Cabling Output relays 1-4

Cabling Output Latching relays 5 & 6

Controller config

STATE (relay)

Normally 

Open (NO) (11-14)

Normally 

Closed (NC) (11-12)

Normally 

Open (NO) (61-64)

Normally 

Closed (NC) (61-62)

Output configured as NO
NO by default

OFF (not active)

Open

Closed

Open

Closed

ON (activated by firmware)

Closed

Open

Closed

Open

Controller not supplied

Open

Closed

Closed*

Open*

Output configured as NC

OFF (not active)

Closed

Open

Closed

Open

ON (activated by firmware)

Open

Closed

Open

Closed

Controller not supplied

Open

Closed

Closed*

Open*

* HZI855 controller includes two bi-stable relays with backup energy, when the controller loses all sources of power supply outputs 5 and 6 will automatically 

activate (NO contact will close and NC contact will open). This is a safety feature designed to ensure power availability to the load in Main-Genset or Genset-Genset 

application by forcing generators to start in case of total power loss. It is highly recommended to configure the outputs 5 and 6 to take benefit from this function.

Summary of Contents for HZI855


































































Reviews:

No comments