GVS ADLD-04/03.1 User Manual Download Page 3

Page: 3 / 58

Contents

Chapter 1 Introduction

----------------------------------------------------------------------------------------------------------------

1.1. Universal Dimming Actuator

----------------------------------------------------------------------------------------------

1.2. Dimming Controller, 4fold, 0~10V

---------------------------------------------------------------------------------------

1.3. Dimming Controller, 4fold, 0/1~10V

------------------------------------------------------------------------------------

1.4. LED Dimming Actuator, 4fold, 350mA

---------------------------------------------------------------------------------

1.5. LED Dimming Actuator, 4fold, 4A

-------------------------------------------------------------------------------------

1.6. Dimming master, 4fold and dimming slave, 2fold, 5A

---------------------------------------------------------

1.7. Triac Dimming Actuator

---------------------------------------------------------------------------------------------------

Chapter 2 Technical characteristic

---------------------------------------------------------------------------------------------

2.1. Universal Dimming Actuator KA/D xx03.1

-------------------------------------------------------------------------

2.1.1 Technical data

------------------------------------------------------------------------------------------------------------

2.1.2 Load type

------------------------------------------------------------------------------------------------------------------

2.1.3 Dimming operation mode

-------------------------------------------------------------------------------------------

2.2. Dimming controller, 4fold, 0~10VKA/D 04.T1.1

-------------------------------------------------------------------

2.2.1 Technical data

------------------------------------------------------------------------------------------------------------

2.3. Dimming controller, 4fold, 0/1~10V ADTV-04/16.1

--------------------------------------------------------------

2.3.1 Technical data

------------------------------------------------------------------------------------------------------------

2.4. LED Dimming Actuator, 4fold, 350mAKA/D 04.L1.1

------------------------------------------------------------

2.4.1 Technical data

------------------------------------------------------------------------------------------------------------

2.5. LED Dimming Actuator, 4fold, 4A ADLD-04/03.1

-----------------------------------------------------------------

2.5.1 Technical data

------------------------------------------------------------------------------------------------------------

2.6. Dimming master, 4fold, KA/D 0400.1 and Dimming slave, 2fold, 5A ADDS-02/05.1

----------------

2.6.1 Technical data -- KA/D 0400.1

--------------------------------------------------------------------------------------

2.6.2 Technical data -- ADDS-02/05.1

------------------------------------------------------------------------------------

2.7. Triac Dimming Actuator KA/D xx15.S.1

-----------------------------------------------------------------------------

2.7.1 Technical data

------------------------------------------------------------------------------------------------------------

Chapter 3 Dimension and Connection Diagram

--------------------------------------------------------------------------

3.1. Universal Dimming Actuator

--------------------------------------------------------------------------------------------

3.1.1 KA/D 0103.1

---------------------------------------------------------------------------------------------------------------

3.1.2 KA/D 0203.1

---------------------------------------------------------------------------------------------------------------

3.1.3 KA/D 0403.1

---------------------------------------------------------------------------------------------------------------

3.2. Dimming controller, 4fold, 0~10V KA/D 04.T1.1

------------------------------------------------------------------

3.3. Dimming controller, 4fold, 0/1~10V ADTV-04/16.1

--------------------------------------------------------------

3.4. LED Dimming Actuator, 4fold, 350mA KA/D 04.L1.1

-----------------------------------------------------------

3.5. LED Dimming Actuator, 4fold, 4A ADLD-04/03.1

-----------------------------------------------------------------

3.6. Dimming master, 4fold KA/D 0400.1

-------------------------------------------------------------------------------

3.7. Dimming slave, 2-fold, 5A ADDS-02/05.1

-------------------------------------------------------------------------

3.8. Triac Dimming Actuator

---------------------------------------------------------------------------------------------------

3.1.1 KA/D 0215.S.1

------------------------------------------------------------------------------------------------------------

3.1.2 KA/D 0415.S.1

------------------------------------------------------------------------------------------------------------

Summary of Contents for ADLD-04/03.1



























































Search results

Summary of Contents for ADLD-04/03.1

Reviews:

Related manuals for ADLD-04/03.1

Brands by name

Popular brands

GVS ADLD-04/03.1, User Manual

Search results

Summary of Contents for ADLD-04/03.1

Reviews:

Related manuals for ADLD-04/03.1

Brands by name

Popular brands