Guangzhou ZHIYUAN Electronics PA5000 Series User Manual Download Page 7

Page: 7 / 98

Date: 2016/12/08

User Manual

V1.00

Guangzhou ZHIYUAN Electronics Co., Ltd.

PA5000 Series Power Analyzer Start Guide

Measurement Category

PA Power Analyzer is at the category of CAT II (1000V). Its input can be connected to

the power supply within the CAT II condition (Max. 1000VAC). Do not use in the

measurement category above CAT II (1000V).

Measurement Category

Ⅵ

It is applicable to measure for the terminal of the

low-voltage facilities



For example, electricity meters, measurement of

primary over current protection devices and ripple

control units, overhead line and cable system.

Measurement Category

Ⅲ

It is applicable to measure for building facilities



For example, measured for the output socket,

industrial device and other devices of the distribution

board, circuit breaker and wirings include cables, bus

bars, junction boxes, switches and fixed facilities,

such as those stationary motors permanently

attached to fixed facilities.

Measurement Category

Ⅱ

It is applicable to measure for circuits directly connected

to the low-voltage device



For example, measured for household appliances,

portable tools and other similar devices.

Measurement Category 0

It is applicable to measure for the circuit not directly

connected with main supply



For example, measured for the circuit which is not

supplied by main supply or measured for the circuit

which is supplied by main supply especially with

internal protection. In the latter case, the transient

stress is not the same. If the instrument is used for

this measurement category, pleasure ensure that the

transient voltage is less than or equal to 3000V peak

value.

Summary of Contents for PA5000 Series



































































































Search results

Summary of Contents for PA5000 Series

Reviews:

Related manuals for PA5000 Series

Brands by name

Popular brands

Guangzhou ZHIYUAN Electronics PA5000 Series, User Manual

Search results

Summary of Contents for PA5000 Series

Reviews:

Related manuals for PA5000 Series

Brands by name

Popular brands