Guangzhou ZHIYUAN Electronics PA5000 Series User Manual Download Page 83

Page: 83 / 98

Date: 2016/12/08

User Manual

V1.00

Guangzhou ZHIYUAN Electronics Co., Ltd.

PA5000 Series Power Analyzer Start Guide

Exception

Handling methods

The data cannot be

saved into the

selected memory

media.

If necessary, please format the memory media.

Please check the remaining space of memory media. Delete the

unnecessary file or replace a new media as needed.

The operation cannot

be set or controlled

via the

communication

interface.

Check whether the settings of GPIB address or serial port conform to the

specifications.

Check whether the interface is satisfied with electrical and mechanical

specifications.

7.2 Recommended Accessory Replace Period

The following accessories are recommended to be replaced regularly. Please contact

ZHIYUAN Electronics for accessory replace.

Table 7-2: Recommended accessory replace period

Accessory name

Recommended replace period

Fan

3 years

Backup battery

3 years

Summary of Contents for PA5000 Series



































































































Search results

Summary of Contents for PA5000 Series

Reviews:

Related manuals for PA5000 Series

Brands by name

Popular brands

Guangzhou ZHIYUAN Electronics PA5000 Series, User Manual

Search results

Summary of Contents for PA5000 Series

Reviews:

Related manuals for PA5000 Series

Brands by name

Popular brands