Guangzhou ZHIYUAN Electronics PA5000 Series User Manual Download Page 37

Page: 37 / 98

Date: 2016/12/08

User Manual

V1.00

Guangzhou ZHIYUAN Electronics Co., Ltd.

PA5000 Series Power Analyzer Start Guide

ratio.



Function operation status indicator

. Display scale factor function, filter, and

the averaging function with enable or disable status.



Data update rate

. It shows the current data update rate of the instrument.



Integral state.

It shows the current integral state and integral time parameters.

The integral state includes Start, End, Error, Reset and Ready. The displayed

integral time parameters depend on the specified integral mode. The integral

time parameters include specified timer time, integral start time, and integral end

time, integral runtime, etc.



Page number

. It shows the number of the page where the current measurement

data is displayed.



Input element indicator

. Used to indicate the currently selected measurement

unit to be configured.



System date/time

. It shows the current date and time.



USB and Ethernet connection status

. It shows the USB and Ethernet

connection status. For detailed information please see Table 3-1.



Internal memory usage.

Its shows the internal memory usage of the power

analyzer.



Common setting

. Press this key to display the common setting interface, as

shown in Figure 3-3, so that users can quickly enter into the common settings on

the touch screen.



Sampling data update rate.

It shows the number of data sampling points for

each input element during measurement.

Table 3-1: Connection status display

Connection Status

Corresponding Icon

USB device connected

USB device not connected

Ethernet connected

Ethernet not connected

Summary of Contents for PA5000 Series



































































































Search results

Summary of Contents for PA5000 Series

Reviews:

Related manuals for PA5000 Series

Brands by name

Popular brands

Guangzhou ZHIYUAN Electronics PA5000 Series, User Manual

Search results

Summary of Contents for PA5000 Series

Reviews:

Related manuals for PA5000 Series

Brands by name

Popular brands