Guangzhou ZHIYUAN Electronics PA5000 Series User Manual Download Page 28

Page: 28 / 98

Date: 2016/12/08

User Manual

V1.00

Guangzhou ZHIYUAN Electronics Co., Ltd.

PA5000 Series Power Analyzer Start Guide

Figure 2-14: Vector display

2.7.7

Flicker Analysis

Power analyzer provides flicker analysis function, which complies with the

international standard IEC61000-4-15 and measurement standard IEC61000-3-3.

Voltage fluctuation caused by instability of light illumination results in the visual

response of human eyes, which known as flicker. The power analyzer measures the

relative steady-state voltage change dc, the maximum relative voltage change dmax,

the time exceeding the threshold relative to the voltage change d(t), the short time

flicker value Pst, the long-time flicker value Plt (manual measurement can only test

dmax) and determines whether it exceeds the normal value so as to assess the

flicker level. Flicker analysis manual measurement view and automatic measurement

view are shown in Figure 2-15 and Figure 2-16 respectively.

Summary of Contents for PA5000 Series



































































































Search results

Summary of Contents for PA5000 Series

Reviews:

Related manuals for PA5000 Series

Brands by name

Popular brands

Guangzhou ZHIYUAN Electronics PA5000 Series, User Manual

Search results

Summary of Contents for PA5000 Series

Reviews:

Related manuals for PA5000 Series

Brands by name

Popular brands