background image

 

                                                                             

 

 

 

 
USER MANUAL 

 

Suzhou Sate Auto Electronic Co., Ltd 

www.sate.com.cn 

 

---------------------------------------------------------------------------------------------------------------------- 

 

Table of Contents 

I. S&T TPMS1209C01, Full-time Direct TPMS------------------------------------------------------------------2 

II. Parts of TPMS1209C01-------------------------------------------------------------------------------------------2 

III. Installation of TPMS1209C01-----------------------------------------------------------------------------------4 

Installation of Monitor------------------------------------------------------------------------------------------------4 

Installation of Transmitter--------------------------------------------------------------------------------------------4 

Installation of Counterweight ---------------------------------------------------------------------------------------6 

IV. Standard Pressure Inquiry and Programming----------------------------------------------------------------- 6 

  Access of Programming Index Interface--------------------------------------------------------------------------6 

Standard Pressure Inquiry --------------------------------------------------------------------------------------------7 

Standard Pressure Programming-------------------------------------------------------------------------------------8 

V. System Time Inquiry and Programming-------------------------------------------------------------------------9 

System Time Inquiry --------------------------------------------------------------------------------------------------9 

System Time Programming------------------------------------------------------------------------------------------10 

VI. System Functions-------------------------------------------------------------------------------------------------10 

VII. Pressure and Temperature Unit Inquiry and Programming-------------------------------------------------15 

Pressure and temperature unit inquiry-------------------------------------------------------------------------------15 

Pressure Unit Programming-------------------------------------------------------------------------------------------16 

Temperature Unit Programming--------------------------------------------------------------------------------------16 

VIII. New Transmitter Adding or Transmitter Replacement------------------------------------------------------17 

IX. Deletion of Transmitter ID----------------------------------------------------------------------------------------20 

X. Specifications -------------------------------------------------------------------------------------------------------22 

XI. Special Annex------------------------------------------------------------------------------------------------------22 

XII. Frequently Asked Questions ------------------------------------------------------------------------------------22 

XIII. Warranty Term ---------------------------------------------------------------------------------------------------23 

XIV. Important Notes---------------------------------------------------------------------------------------------------23 

 

Summary of Contents for TPMS1209C01
























Reviews: