manualshive.com logo in svg

GSi TopDry Autoflow, Construction Manual

Share
Download
GSi TopDry Autoflow Construction Manual Download Page 84

Chapter 7: TopDry Drying Floor

Installing the Leveling Band

1. Position the leveling bands as shown.

2. Install the leveling bands to the leveling band posts (F) using 5/16 x 1 in. flange bolts (D) and

5/16 in. flange nuts (E).

NOTE:

Install the levelling bands starting from the bottom of the levelling band posts (F).

3. Connect the leveling bands together using 5/16 x 1 in. flange bolts (D) and 5/16 in. flange nuts (E) at

the overlaps at every fourth hole.

NOTE:

The band sections connect to each other only at end most holes when completing the circle
where an overlap may occur.

Figure 7-22

Inner leveling bands

5 Band sections per ring

6 Bays with 20 holes between posts

A

6-3/16 in.

E

5/16 in. flange nut (S-3611)

B

6-3/8 in.

F

Leveling band post

C

2-3/8 in.

G

Perforated center band suspended from
roof panels

D

5/16 x 1 in. flange bolt with sealing washer
(S-10260)

84

PNEG-4936

36 Ft. TopDry Autoflow

Summary of Contents for TopDry Autoflow















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands