manualshive.com logo in svg

GREAT PLAINS 3S-4000HD, Operator'S Manual, Page: 103 / 118

Share
Download
GREAT PLAINS 3S-4000HD Operator'S Manual Download Page 103

100

3S-4000HD/HDF

Table of Contents Index

Great Plains Manufacturing, Inc.

195-067M

Table of Contents Index

2019-03-14

Small Seeds Attachment

These kits deliver the smallest seeds evenly and gently. 

A kit adds to each main seed box: a clutched drive line, a 

second seed box, small seed fluted feeder cups, seed 

drop tubes for each row, and all necessary hardware.
Small Seeds capability may be specified on the initial drill 

order (Sequence No. 91), or added later (post-2004 drills 

only).

For operation, see “

Loading Seed

” on page 38 and the 

Seed Rate Manual.

Removable Partition

This partition reduces side-to-side seed flow in the small 

seeds box. This can prevent seed pile-up when drilling 

across slopes and in other situations where the seed is 

particularly fluid. Order one per partition.

Seed Tube Plug (Small Seeds)

This plug stops seed flow from the small seeds box 

above the meter. Order one per row to set inactive.

Description

Part

Number

3S-4000HD-4810 10 in. Small Seeds

133-302A

3S-4000HD-6375 7.5 in. Small Seeds

133-300A

3S-4000HD-7806 6 in. Small Seeds

133-301A

3S4000HDF-4810 10 in. Small Seeds

133-321A

3S4000HDF-6375 7.5 in. Small Seeds

133-320A

3S4000HDF-7806 6 in. Small Seeds

133-319A

Description

Part 

Number

RMVBL SMALL SEED BOX PARTITION

123-409D

26499

17028

Description

Part Number

SML SDS CUP PLUG

133-315H

FigureSpacer

27407

Summary of Contents for 3S-4000HD























































































































Reviews:

No comments