GREAT PLAINS 3S-4000HD Operator'S Manual Download Page 68

Page: 68 / 118

Great Plains Manufacturing, Inc.

Table of Contents Index

Adjustments

2019-03-14

Table of Contents Index

195-067M

Opener Depth (Press Wheel Height)

Refer to Figure 74

Set opener seeding depth

by adjusting press-wheel

height

To adjust, first raise openers slightly, then lift and slide

the T handle

on top of each opener. Adjust all press

wheels to the same height.
• Each increment of the handle adjusts the seeding

depth by approximately



inch (6.4 mm). The range

is approximately 0 to 3



inches (0 to 8.9 cm) seeding

depth.

• For more shallow seeding, slide T handle forward

toward implement.

• For deeper seeding, slide T handle backward

away

from implement.

If press wheels are lifting off ground, increase hydraulic

down pressure.
If press wheels are digging into ground, reduce hydraulic

down pressure.

Figure 74

Adjusting 00HD Opener Depth

26441

Summary of Contents for 3S-4000HD























































































































Search results

Summary of Contents for 3S-4000HD

Reviews:

GREAT PLAINS 3S-4000HD, Operator'S Manual, Page: 68 / 118

Search results

Summary of Contents for 3S-4000HD

Reviews: