GREAT PLAINS 3S-4000HD Operator'S Manual Download Page 30

Page: 30 / 118

Great Plains Manufacturing, Inc.

Table of Contents Index

Operating Instructions

2019-03-14

Table of Contents Index

195-067M

Folding

Crushing Hazard:

Keep all persons well away during folding operation.

Bystanders could be crushed between the folding drill boxes
and the drill tongue.

1. Park tractor and drill on level ground with tractor

transmission in Park. Be aware of clearance needed

to fold drill.

2. Fold up markers if installed. See “

Marker

Operation

” on page 43. Return selector valve

handle to Fold position.

Refer to Figure 18

3. Opener subframe must be raised for folding. Position

all six opener lock handles in ROAD position and

completely raise openers. See “

Raising and

Lowering Openers

” on page 26.

Note: The opener transport lock handles are spring

loaded and can be moved to ROAD position with

openers up or down, but locks only engage when

openers are completely raised. There are two locks

on each drill section.

4. Make sure transport lift cylinders and front box lift

cylinder are completely retracted (drill is lowered,

although openers are raised).

5. Slowly supply oil to rod (retract) end of fold circuit.

Completely fold wing frames until both wing gauge

wheels contact tongue tube.

Fold (for transport) is not complete until Transport Lift is

completed. In particular, the transport hooks only

engage, lift and secure the wings as part of Transport Lift

(the next topic).
6. Allow transport lift cylinders to settle back against

lock channels.

7. Before transporting, check that hydraulic cylinders

are holding lock channels securely.

Figure 18 - Fold

Opener Lock Up

15549

Summary of Contents for 3S-4000HD























































































































Search results

Summary of Contents for 3S-4000HD

Reviews:

GREAT PLAINS 3S-4000HD, Operator'S Manual, Page: 30 / 118

Search results

Summary of Contents for 3S-4000HD

Reviews: