manualshive.com logo in svg

GREAT PLAINS 3S-4000HD, Operator'S Manual, Page: 101 / 118

Share
Download
GREAT PLAINS 3S-4000HD Operator'S Manual Download Page 101

195-067M

Table of Contents Index

2019-03-14

98

3S-4000HD/HDF

Table of Contents Index

Great Plains Manufacturing, Inc.

Options

Hitches

One hitch is selected upon initial order of a 

3S-4000HD/HDF Drill, and includes the spring wire loop, 

safety chain, and all fasteners. Additional hitches may be 

ordered for conversion in the field, and include extra 

hitch mounting bolts, lock washers and nuts.

Open Center Conversion

The standard 3S-4000HD/HDF drill is compatible with 

tractors having “active” or “closed center” hydraulic 

systems. For use with “non-active” or “open center” 

tractors, a conversion kit is available. Order one kit per 

drill.

For operations, see “

Tractors with Open Center 

Hydraulics

” on page 22.

Two Outlet Hydraulic Kit

The standard 3S-4000HD/HDF drill requires three 

remote outlet circuits on the tractor. If only two are 

available, this kit enables the Transport and Opener Lift 

circuits to share a single remote, via a selector valve on 

the tongue at the hitch. Order one kit per drill.

For operations, see “

Lift Selector Valve Operation

” on 

page 44.

Hitch Description

Part Numbers

 Large Strap

170-038A

 Clevis

170-039A

 Small Strap

170-059A

26487

1

2

3

1

2

3

Description

Part Number

Open Center Hydraulic Kit

194-143A

18750

Description

Part Number

Two Outlet Tractor Conversion

194-122A

15550

Summary of Contents for 3S-4000HD























































































































Reviews:

No comments