manualshive.com logo in svg

GREAT PLAINS 3S-4000HD, Operator'S Manual, Page: 76 / 118

Share
Download
GREAT PLAINS 3S-4000HD Operator'S Manual Download Page 76

2019-03-14

Table of Contents Index

195-067M

Great Plains Manufacturing, Inc.

Table of Contents Index

73

Maintenance and Lubrication

Proper servicing and maintenance is the key to long 

implement life. With careful and systematic inspection, 

you can avoid costly maintenance, downtime and repair. 
Always turn off and remove the tractor key before 

making any adjustments or performing any maintenance. 

Crushing Hazard:

You may be severely injured or killed by being crushed under a 
falling implement. Always have frame sufficiently blocked up 

when working on, and particularly under implement.

High Pressure Fluid Hazard:

Check all hydraulic lines and fittings before applying pressure. 

Use paper or cardboard, not body parts, and wear heavy 
gloves to check for suspected leaks. Escaping fluid under 

pressure can have sufficient pressure to penetrate the skin. 

Fluid escaping from a very small hole can be almost invisible. 
If injured, seek immediate medical attention from a physician 

familiar with this type of injury.

After using drill for several hours, check all bolts to be 

sure they are tight.
1. Securely block drill before working on it.
2. Lubricate areas listed under “

Lubrication and 

Scheduled Maintenance

” on page 90.

3. Clean any fittings that do not take grease.
4. Inflate tires as specified on “

Tire Inflation Chart

” on 

page 103.

5. Inspect hydraulic hoses for cuts, cracks and aging. 

Check fittings for evidence of leaks.

6. Keep disk scrapers properly adjusted.
7. Replace any worn, damaged or illegible safety 

decals. Order new decals from your Great Plains 

dealer. “

Safety Decals

” on page 7.

Summary of Contents for 3S-4000HD























































































































Reviews:

No comments