GREAT PLAINS 3S-4000HD Operator'S Manual Download Page 97

Page: 97 / 118

3S-4000HD/HDF

Table of Contents Index

Great Plains Manufacturing, Inc.

195-067M

Table of Contents Index

2019-03-14

Mainframe Pivots

2 zerks each pivot; 4 total
Type of Lubrication: Grease

Quantity: Until grease emerges

On newer drills, these zerks are served by a grease bank

on the top of the wing. On older drills, these zerks are

more accessible with the drill folded.

Seed Cup Drive Shaft Sprocket

2 sliding sprockets; one each side

Type of Lubrication: Oil

Quantity: Coat thoroughly

Move the Seed Rate adjustment handle back and forth to

get oil into the square bore. Perform this with seed box

empty, or handle may be difficult to set to 100.

Gauge Wheel Chain

1 chain per gauge wheel; 2 total
Type of Lubrication: Chain Lube

Quantity: Coat thoroughly
Slack:



inch (13 mm) in top span

18792

12126

As Required

18865

Summary of Contents for 3S-4000HD























































































































Search results

Summary of Contents for 3S-4000HD

Reviews:

GREAT PLAINS 3S-4000HD, Operator'S Manual, Page: 97 / 118

Search results

Summary of Contents for 3S-4000HD

Reviews: