GREAT PLAINS 3S-4000HD Operator'S Manual Download Page 85

Page: 85 / 118

3S-4000HD/HDF

Table of Contents Index

Great Plains Manufacturing, Inc.

195-067M

Table of Contents Index

2019-03-14

Align Transfer Drive Shaft

Refer to Figure 91 and Figure 92

After wing boxes are properly aligned, the transfer drive

shaft must be aligned so the pair of break-away jaws

are fully engaged and are concentric. The



in hex drive

shafts holding the clutch jaws should not contact each

other

when wing boxes are properly aligned and back

against their stops.
1. Place a 4



4 inch (10



10 cm) or similar sized block

ahead of the wing gauge wheels and pull forward or

push wing box frames back until the tool bar is firmly

against tool bar stop bolts on the center box frame.

2. To align the clutch jaws vertically, loosen the two



inch bolts

on the backside of the adjustment

plate

. Slide the plate up or down in the desired

direction. Tighten bolts.

Figure 91

Transfer Drive Jaws

18955

Figure 92

Transfer Drive Shaft Vertical Adjustment

18953

Summary of Contents for 3S-4000HD























































































































Search results

Summary of Contents for 3S-4000HD

Reviews:

GREAT PLAINS 3S-4000HD, Operator'S Manual, Page: 85 / 118

Search results

Summary of Contents for 3S-4000HD

Reviews: