GREAT PLAINS 3S-4000HD Operator'S Manual Download Page 88

Page: 88 / 118

Great Plains Manufacturing, Inc.

Table of Contents Index

Maintenance and Lubrication

2019-03-14

Table of Contents Index

195-067M

Opener-Frame Clearance

Refer to Figure 97

When fully raised, top of opener mounts

should clear

bottom of drill frame tube by at least



inch (12.7 mm).

To adjust opener frames so all openers have the same

clearance, loosen jam nut

on opener lift cylinders and

turn adjustment nut. When openers are at the correct

height, retighten jam nut. Repeat at each opener lift

cylinder if necessary.

Drive System

For proper operation and to prevent downtime and

repair, keep drive chains properly adjusted and

lubricated. Regularly check drive chains for excess slack

and wear. Adjust idlers to remove any excess slack from

chains.

Refer to Figure 98

Note: Be sure chains are installed with the chain

connector link retainers towards machine

centerline and the clip openings (split end) facing

away from the direction of chain travel.

Figure 97

Opener Frame Clearance

18853

Figure 98

Chain Connector Link Clip

26482

Summary of Contents for 3S-4000HD























































































































Search results

Summary of Contents for 3S-4000HD

Reviews:

GREAT PLAINS 3S-4000HD, Operator'S Manual, Page: 88 / 118

Search results

Summary of Contents for 3S-4000HD

Reviews: