manualshive.com logo in svg

GREAT PLAINS 3S-4000HD, Operator'S Manual, Page: 51 / 118

Share
Download
GREAT PLAINS 3S-4000HD Operator'S Manual Download Page 51

48

3S-4000HD/HDF

Table of Contents Index

Great Plains Manufacturing, Inc.

195-067M

Table of Contents Index

2019-03-14

Total Acres

Refer to Figure 48

Press the FUNC button until the “TOTAL” legend 

appears in the display. The digits indicate the acres 

covered since the total acre counter was last cleared to 

zero.
To clear the total acre count, press and hold the UP and 

DOWN buttons for 2 seconds.
Note: If a passcode is set, it must be entered to clear the 

total acre count. 

Total acres count from 1 to 99999 acres.

Pulses per Mile

Press the FUNC button until the “PULSES” legend 

appears in the display. The number in the display 

indicates shaft rotations for one mile.
Note: If a passcode is set, it must be entered to adjust the 

pulses per mile.

There are two methods to enter the pulses per mile.

Known Pulses Values

Refer to Figure 48

1. If you know the number, select it using the UP and 

DOWN buttons. When you press the FUNC button, 

the controller accepts the number in the display as 

the new pulses per mile. Approximate pulses per 

mile for 3S-4000HD/HDF row spacings are:

Figure 48

Total Acres Display

26479

2 of 8

Model

Spacing

Pulses

3S-4000HD/HDFF-4810

10 in

214

3S-4000HD/HDFF-6375

7.5 in

212

3S-4000HD/HDF-7806

6 in

212

Figure 49

Pulses Per Mile Entry

26479

3 of 8

Summary of Contents for 3S-4000HD























































































































Reviews:

No comments