manualshive.com logo in svg

GREAT PLAINS 3S-4000HD, Operator'S Manual, Page: 75 / 118

Share
Download
GREAT PLAINS 3S-4000HD Operator'S Manual Download Page 75

72

3S-4000HD/HDF

Table of Contents Index

Great Plains Manufacturing, Inc.

195-067M

Table of Contents Index

2019-03-14

Openers raise when tractor 

hydraulic lever is held forward 

and lower when lever is held 

back

Reverse hydraulic hoses at tractor 

quick couplers.

Opener frames do not float over 

uneven terrain

Hydraulic lever not locked forward.

Lock hydraulic lever forward.

Openers not connected to circuit 

designed for hydraulic motor control.

Refer to page 34.

Pressure gauges read zero when 

openers are lowered and 

tractor hydraulic lever is held 

forward

Hydraulic hoses not routed correctly 

between pressure control valves and 

opener lift cylinders.

See hose routing diagrams beginning 

on page 105.

Pressure gauges show pressure 

when openers are raised

Hydraulic hoses not routed correctly 

between pressure control valves and 

opener lift cylinders.

See hose routing diagrams beginning 

on page 105.

Transport lock channels will not 

stay in position for transport

U-shaped clip in lock channel not 

clasping cylinder rod securely.

Tighten or loosen clip by turning bolt 

on clip. Replace clip if necessary.

Hydraulic cylinders have not settled 

against lock channels before 

transporting.

Make sure hydraulic cylinders have 

settled against lock channels before 

transporting. The weight of the 

cylinders help hold lock channels in 

place.

Hydraulic marker functioning 

improperly

Air or oil leaks in hose fittings or 

connections.

Check all hose fittings and connections 

for air or oil leaks.

Low tractor hydraulic oil level.

Check tractor hydraulic oil level.

Loose or missing bolts or fasteners.

Check all bolts and fasteners.

Needle valve plugged.

Open needle valve, cycle markers 

slowly and reset needle valve, refer to 

page 68.

Marker disk does not mark

Marker folding linkage does not have 

enough slack to allow marker disk to 

drop into field depressions.

Maximum down float should be limited 

by the slot at the rod end of marker 

cylinder.

Reverse marker disk to pull or throw 

dirt.

Chain

Debris/no retainer clip

Be sure retainer clip is facing opposite 

way of chain travel

Problem

Cause

Solution

Summary of Contents for 3S-4000HD























































































































Reviews:

No comments