manualshive.com logo in svg

GREAT PLAINS 3S-4000HD, Operator'S Manual, Page: 34 / 118

Share
Download
GREAT PLAINS 3S-4000HD Operator'S Manual Download Page 34

Great Plains Manufacturing, Inc.

Table of Contents Index

Operating Instructions

31

2019-03-14

Table of Contents Index

195-067M

Transport Checklist

Before transporting the drill, check the following items:

Lowering Drill (Transport Lift)

Lowering from Transport Lift must be completed prior to 

unfolding.
Transport Lift is on a dedicated hydraulic circuit. The 

center main frame raises and lowers independently of 

the opener sub-frames (which are raised and lowered by 

the Opener Lift circuit).
The Transport Lift circuit also includes a cylinder for the 

Transport Hooks, which lifts and restrains the 

outer/forward ends of the wing sections when folded.
Transport Lift is normally used only when the drill is 

folded. Opener Lift, and not Transport Lift, is used for 

headland turns in field operations.

Transport only with a tractor of proper size. 

See “

Specifications and Capacities

” on page 103.

Safety Chain in Place

 (page 17)

 - 

Attach safety chain 

to an anchor on tractor.

Drill Securely Hitched

 (page 17)

 - 

Always use a 

locking-style pin sized to match holes in hitch and 

draw bar (minimum of 1 inch (2.4 cm) diameter).

Openers Raised and Locked

 (page 26) - Lock 

openers up into ROAD position.

Tires

 (page 103)

 - 

Check that all tires are properly 

inflated

Bystanders - 

Check that no one is in the way before 

moving. Do not allow anyone to ride on the drill.

Warning Lights - 

Always use tractor and drill warning 

lights in transport.

Clearance

 (page 103)

 - 

Know the maximum 

dimensions of the drill in transport position and follow 

a route that provides adequate clearance from all 

obstructions.

Stopping Distance - 

Allow sufficient stopping 

distance and reduce speed prior to any turns or 

maneuvers. If the drill is transported full, allow extra 

stopping distance.

Road Rules -

Comply with all national, regional and 

local laws when transporting on public roads.

Parking Stands Raised

 (page 53) - Rotate stands up 

and pin.

Walkboard Ladders Raised

 - (if equipped)

3S-4000HD/HDF Drill Raised and Locked

 (page 28)

 

- 

Make sure drill is folded properly. Secure cylinder 

lock channels on transport-cylinder rods and front box 

lift cylinders. Allow transport lift cylinders to settle 

against lock channels.

Figure 24

Locked-Up Transport Lift

26491

Summary of Contents for 3S-4000HD























































































































Reviews:

No comments