GREAT PLAINS 3S-4000HD Operator'S Manual Download Page 2 | Manualshive

Page: 2 / 118

GREAT PLAINS 3S-4000HD Operator'S Manual Download Page 2

Great Plains Manufacturing, Inc.

ii

2019-03-14

195-067M

©

Copyright 2000, 2006, 2007, 2009, 2010, 2012, 2013, 2019 2019 All rights Reserved

Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been
taken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed
for damages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products
as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.

Trademarks of Great Plains Manufacturing, Inc. include: AccuShot, Max-Chisel, Row-Pro,

Singulator Plus, Short Disk, Swath Command, Terra-Tine, Ultra-Chisel, and X-Press.

Registered Trademarks of Great Plains Manufacturing, Inc. include: Air-Pro, Clear-Shot, Discovator, Great Plains, Land Pride, MeterCone,

Nutri-Pro, Seed-Lok, Solid Stand, Terra-Guard, Turbo-Chisel, Turbo-Chopper, Turbo-Max, Turbo-Till, Ultra-Till, Whirlfilter, and Yield-Pro.

Brand and Product Names that appear and are owned by others are trademarks of their respective owners.

Printed in the United States of America

Table of Contents

Important Safety Information ......................................1

Safety Decals .................................................................7

Introduction ................................................................14

Document Family .........................................................14

Description of Unit ........................................................14

Intended Usage ........................................................14

Models Covered .......................................................14

Definitions.................................................................15

Preparation and Setup ...............................................17

Hitching ........................................................................17

Electrical Connections..................................................19

Hydraulic Hose Hookup................................................20

Check Drill Level ..........................................................21

Setting the Bypass Valve .............................................22

Scraper Installation.......................................................23

Marker Setup................................................................24

Operating Instructions...............................................25

General Description......................................................25

Pre-Start Checklist .......................................................25

Raising and Lowering Openers ....................................26

Opener Lock Up ...........................................................26

Lock Up Openers..................................................26

Unlock Openers....................................................26

Folding..........................................................................27

Raising Drill (Transport Lift)..........................................28

Transport Lift ............................................................28

Transport ......................................................................30

Tractor Requirements...............................................30

Marker Transportation ..............................................30

Transport Checklist ..................................................31

Lowering Drill (Transport Lift) .......................................31

Transport Lower .......................................................32

Unfolding ......................................................................33

Folding and Unfolding Quick Reference...................33

To Fold Drill for Transport.....................................33

To Unfold Drill for Field.........................................33

Opener Operation.........................................................34

Active Hydraulic Systems.........................................35

Priority Flow Hydraulic Systems ...............................36

Non-Active Hydraulic Systems .................................36

Loading Seed ...............................................................38

Main Seed Box Loading ...........................................38
Small Seeds Box Loading ........................................38

Initial Seeding Depth ................................................39

Fertilizer Box Operation ............................................... 39

Seeding and applying fertilizer ................................. 39

Divided Capacities ............................................... 40

Divider Removal................................................... 40

Seeding with Both Compartments ........................... 42

Marker Operation ......................................................... 43

Single Marker Operations ........................................ 43

Dual Marker Operations........................................... 43

Lift Selector Valve Operation ....................................... 44

Point Row Operation.................................................... 44

Shaft Monitor Operation............................................... 45

Acremeter Installation (S/N )......................... 45

Acremeter Operation (S/N ) .......................... 46

Normal Operating Sequence ................................... 46

Dormant Display................................................... 46

Digital Acremeter Operation (S/N YY1735-) ................ 47

Field Operations........................................................... 52

Final Field Checklist ................................................. 52

Parking......................................................................... 53

Parking with Drill Folded .......................................... 54

Storage ........................................................................ 54

Adjustments ............................................................... 55

Seed and Fertilizer Rate ...................................... 55

Planting Depth...................................................... 55

Frame Level ................................................................. 56

Frame Weight .............................................................. 57

Opener Frame Down-Force ......................................... 58

Setting Hydraulic Down-Pressure ............................ 59

Opener-Subframe Adjustment ..................................... 60

00HD Row Unit Adjustments ....................................... 61

Opener Height.......................................................... 62

Row Unit Down Pressure (Spring) ........................... 62

Disk Blade Adjustments ........................................... 63

Adjusting Disk Contact ......................................... 63

Disk Scraper Adjustments........................................ 63

Seed Firmer Adjustments ........................................ 64

®

Seed Firmer Adjustment........................ 64

Seed Firmer Lock-Up ........................ 64

Opener Depth (Press Wheel Height) ....................... 65

Marker Adjustments ..................................................... 66

Marker Extension ..................................................... 66

Marker Disk Adjustment........................................... 67

Mark Width ........................................................... 67

Direction of Cut .................................................... 67

Marker Chain Adjustment ........................................ 67

«
1
2
3
4
...
»

Summary of Contents for 3S-4000HD























































































































Reviews:

No comments