manualshive.com logo in svg

GREAT PLAINS 3S-4000HD, Operator'S Manual, Page: 17 / 118

Share
Download
GREAT PLAINS 3S-4000HD Operator'S Manual Download Page 17

195-067M

Table of Contents Index

2019-03-14

14

3S-4000HD/HDF

Table of Contents Index

Great Plains Manufacturing, Inc.

Introduction

Great Plains welcomes you to its growing family of new 

product owners. Your Three-Section Folding HD Drill has 

been designed with care and built by skilled workers 

using quality materials. Proper setup, maintenance, and 

safe operating practices will help you get years of 

satisfactory use from the machine.

Document Family

Description of Unit

The 3S-4000HD and 3S-4000HDF is a towed seeding 

implement. This three section drill has a working width of 

40 feet (12.2 m). The drill has straight arm, double disk 

heavy duty openers. The opener disks make a seed bed, 

and seed tubes mounted between the disks place seed 

in the furrow. Press wheels following the opener disks 

close the furrow and gauge opener seeding depth. A 

T-handle on the opener body is for seeding depth 

adjustments. Seeding rates are adjustable with the seed 

rate adjustment handle and sprocket changes.
The 3S-4000HD/HDF features active hydraulic down 

pressure on the opener frames. When used on a tractor 

with closed-center hydraulics, constant down pressure 

ensures even opener penetration in uneven ground. 

Hydraulic down pressure is adjustable at a single point.

Intended Usage

Use this implement to seed production-agriculture crops 

in conventional or minimum tillage applications.

Models Covered

195-067M Operator manual (this document)
195-067P

Parts manual

195-325B

Seed & Fertilizer Rate manual

195-067Q Dealer Pre-Delivery manual

3S-4000HD-4810

48-Row 10-Inch spacing

3S-4000HD-6375

63-Row 7.5-Inch spacing

3S-4000HD-7806

78-Row 6-Inch spacing

3S4000HDF-4810

48-Row 10-in. with Fertilizer

3S4000HDF-6375

63-Row 7.5-in. with Fertilizer

3S4000HDF-7806

78-Row 6-in. with Fertilizer

Figure 1

3S-4000HD/HDF Drill

18843

Summary of Contents for 3S-4000HD























































































































Reviews:

No comments