GILBARCO VEEDER-ROOT Applause Media System Installation, Service, And Parts Manual Download Page 94

Page: 94 / 102

Installing and Configuring Secondary NIC in Applause Media System Site Server

Configuring Secondary NIC

Page F-2

MDE-4699L Applause™ Media System Installation, Service, and Parts Manual · June 2017

Install the secondary NIC.

Reinstall the Applause Media System Site Server top cover and restore power.

Note: Non-default and secondary NIC settings must be provided by the retail customer’s IT

department. The Gilbarco TAC cannot provide these settings.

Configuring Secondary NIC

To configure the secondary NIC in the Applause Media System Site Server, proceed as
follows:

Connect to the Applause Media System Site Server via laptop.

Navigate to the

Network Setup

page.

Enter the secondary NIC IP configuration information.

Disable routing between NIC if required by the site configuration.

Save the configuration and restart the Applause Media System Site Server.

Summary of Contents for Applause Media System







































































































Search results

Summary of Contents for Applause Media System

Reviews:

Related manuals for Applause Media System

Brands by name

Popular brands

GILBARCO VEEDER-ROOT Applause Media System, Installation, Service, And Parts Manual

Search results

Summary of Contents for Applause Media System

Reviews:

Related manuals for Applause Media System

Brands by name

Popular brands