GILBARCO VEEDER-ROOT Applause Media System Installation, Service, And Parts Manual Download Page 100

Page: 100 / 102

Forwarding System Logs

Page H-2 MDE-4699L Applause™ Media System Installation, Service, and Parts Manual · June 2017

Click

Log Files

. The Log Files screen appears.

Figure G-2: Log Files Screen

To enable log forwarding, enter a Hostname or IP address for the remote server that will
receive the log files, and the appropriate Port Number for the remote server.

Note: The appropriate settings for the remote server should be obtained from the customer for

each location.

Click the

Update

button to save your changes. The changes take effect immediately.

Summary of Contents for Applause Media System







































































































Search results

Summary of Contents for Applause Media System

Reviews:

Related manuals for Applause Media System

Brands by name

Popular brands

GILBARCO VEEDER-ROOT Applause Media System, Installation, Service, And Parts Manual

Search results

Summary of Contents for Applause Media System

Reviews:

Related manuals for Applause Media System

Brands by name

Popular brands