manualshive.com logo in svg

GILBARCO VEEDER-ROOT Applause Media System, Installation, Service, And Parts Manual, Page: 24 / 102

Share
Download
GILBARCO VEEDER-ROOT Applause Media System Installation, Service, And Parts Manual Download Page 24

Start-up

Before Start-up

Page 4-2

MDE-4699L Applause™ Media System Installation, Service, and Parts Manual · June 2017

Installing Software in Gilbarco Site Server

Install the site server software and refer to 

“Configuring Laptop for Communication and 

Programming Site Server”

 on 

page 4-3 

to program the LRE switch before going to the 

site, if possible. This reduces the time required to spend on the phone at the site.

IMPORTANT INFORMATION

The site server software is distributed as a CD-ROM ISO image. It may be burned to a USB 
drive to install the software on a site server that has USB ports but no CD-ROM drive or it 
may be burned onto a CD-ROM to install the software on a site server that has a CD-ROM 
drive.

Note: If you will be installing a secondary Network Interface Card (NIC) on a site server that 

only has one built-in NIC, install the software first, and then install the NIC card. This 
will ensure that the secondary NIC card will be recognized as the “secondary” card by 
the site server software.

Installing Site Server Software from USB Drive

To install the site server software from a USB drive, proceed as follows:

1

Burn the CD-ROM ISO image onto a USB drive, using the “Linux Live USB Creator” utility 
(available from 

http://www.linuxliveusb.com

).

2

Ensure that the Gilbarco Site Server is powered down.

3

Insert the USB drive containing the software in an available USB port on the site server, then 
press the power button on the site server. The setup and installation process begins. The 
installation will take about 10-20 minutes.

When the installation is complete, you will hear a repeating pattern of three short beeps from 
the server. It is recommended that you attach a monitor to the server, however, to be able to see 
the installation progress on screen and verify that the installation is complete. Remove the 
USB drive and press RESET. After the server reboots (about three minutes), it will be ready 
for programming using the laptop.

Notes: 1) If the server does not start beeping within 15 minutes, call TAC and refer to 

“Gilbarco Site Server Software Not Loading”

 on 

page 5-4

.

2) If the Gilbarco Site Server that you have does not have a reset button, press and hold 

the power button until the device powers down, then release the button and press it 
once to turn it back on.

Summary of Contents for Applause Media System







































































































Reviews:

No comments