GEA D-tec D Operating Instruction Download Page 78

Page: 78 / 106

Fig.47

Use the insertion tool to press in the V-ring – evenly press in at several
opposite points along the circumference.

Fig.48

Insert the V-ring evenly.

Replace all the other seals identified in the spare parts lists.

Done

Hint!

Used seals must not be used again, since the proper function of the
seal can then no longer be ensured.

10.7.4 Changing the stem diaphragm

See Section 10.5.2, Page 50 for details on changing the stem diaphragm.
See Section 10.6.1, Page 59 for details on assembly of the stem diaphragm.

10.7.5 Exchanging the O-ring (TEFASEP gold)

Tools required:

•

O-ring cutter

•

Heat-resistant protective gloves

•

Oven (no microwave)

Caution!

Health hazard due to toxic fumes!

The O-ring cutter cuts the seal with a hot metal tip. At temperatures of more
than 300 °C, toxic fumes can be released.
► Avoid directly inhaling the fumes.

Maintenance

Maintenance

430BAL013307EN_8

04.08.2022

Summary of Contents for D-tec D











































































































Search results

Summary of Contents for D-tec D

Reviews:

Related manuals for D-tec D

Brands by name

Popular brands

GEA D-tec D, Operating Instruction

Search results

Summary of Contents for D-tec D

Reviews:

Related manuals for D-tec D

Brands by name

Popular brands