GEA D-tec D Operating Instruction Download Page 75

Page: 75 / 106

Interrupt the compressed air supply to the connection (0).

The valve insert lowers.

Actuator (A) raises to the lift actuator (L).

Lift actuator (A) and place a spacer between the flanges of the actuators
(approx. 25 mm).

Pull the threaded bushing (L8) and the adjusting nut (L6) out of the lift
actuator (L).

Loosen the threaded pin (L7) on the adjusting nut (L6) with a hex socket
wrench.

10.

Turn adjusting nut (L6) according to necessary adjustment (1.5 mm per
revolution):

Reduce stroke: Turn the adjusting nut (L6) clockwise.
(Viewing the valve from above)

Increase stroke: Turn the adjusting nut (L6) anti-clockwise.
(Viewing the valve from above)

11.

Tighten threaded pin (L7) with a hex socket wrench.

Warning!

Risk of injury due to moving valve parts.

► Do not touch between the actuator (A) and lantern (L).

12.

Pressurise actuator at connection (0) with compressed air, max. 8 bar.

The valve insert is raised (main stroke).

Actuator (A) lowers to the lift actuator (L).

13.

Grease the thread of the clamp connections (46) and install.

Ensure that the clamp connections (46) are firmly installed.

! Observe table "Torques for half rings and clamp connections", see
Section 10.6.5, Page 72.

14.

Interrupt the compressed air supply to the connection (0).

15.

Pressurise actuator at connection (Y2) with compressed air, max. 8 bar.

Valve disk is raised.

16.

Measuring lift stroke

Done

10.7

Maintenance

Maintenance

430BAL013307EN_8

04.08.2022

Summary of Contents for D-tec D











































































































Search results

Summary of Contents for D-tec D

Reviews:

Related manuals for D-tec D

Brands by name

Popular brands

GEA D-tec D, Operating Instruction

Search results

Summary of Contents for D-tec D

Reviews:

Related manuals for D-tec D

Brands by name

Popular brands