GEA D-tec D Operating Instruction Download Page 48 | Manualshive

Page: 48 / 106

background image

10.5.1.2 Disconnecting the valve from the housing

Fig.21:

Disconnecting the valve from the housing

Caution!

Risk of injury due to moving valve parts.

► Do not touch the lantern (9).

Warning!

Spring tension in the valve

Danger of injury when opening the clamp connections on the actuator or on
the housing as the released spring pretension will suddenly lift the actuator.
► Therefore, release the spring tension before detaching the clamp
connections by pressurising the actuator with compressed air at max. 8 bar.

Tools required:

•

Open-ended wrench

Carry out the following steps:

1.

Turn the connection (0) with the angled screw-in connection and reduction
nipple in the piston stem.

2.

Vent actuator at connection (0) with compressed air, max. 8 bar.

®

The valve insert is raised.

Maintenance

Disassembling the valve

430BAL013307EN_8

48

04.08.2022

«
...
46
47
48
49
50
...
»

Summary of Contents for D-tec D











































































































Reviews:

No comments

Related manuals for D-tec D

Brand: NEC Pages: 146

Brand: Bartec Pages: 26

Brand: V2 Pages: 48

Brand: Dahua Pages: 58

Brand: ICP DAS USA Pages: 166

Brand: ICP DAS USA Pages: 64

Tunnel Master Jr

Brand: ICS Pages: 83

PROFIBUS PROFI-2510

Brand: ICP DAS USA Pages: 4

Brand: ICP DAS USA Pages: 40

Brand: IFM Pages: 49

Ecomot300 AC2630

Brand: IFM Electronic Pages: 111

Brand: Yamaha Pages: 5

Brand: Yamaha Pages: 20

Brand: Yamaha Pages: 2

Brand: TCi Pages: 9

Brand: Parker Pages: 16

Brand: ZKTeco Pages: 2

Brand: National Instruments Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands