GE Druck DPI 615 IS, User Manual

Page: 57 / 95

K0430 Issue No. 2 48
(5) Set the variable supply voltage to 30V ±0.1V and enter the measured full-scale
voltage:
(6) Press the ENTER key to accept the calibration. Press the EXIT key four times to
quit the CALIBRATION and SETUP modes.
(7) Verify the instrument calibration by applying the test voltages given in Table 2 to
the voltmeter (after both voltage ranges have been calibrated).
(8) Disconnect the calibration/test equipment.
Table 2 Electrical Voltage Input Calibration Tolerances
Voltage Calibration 30V Range Verification Tolerances Voltage Calibration 5V Range Verification Tolerances
Applied Voltage Permissible Deviation Applied Voltage Permissible Deviation
-30 ± 0.05% rdg, ± 0.004% FS -5 ± 0.05% rdg, ± 0.004% FS
-24 ± 0.05% rdg, ± 0.004% FS -4 ± 0.05% rdg, ± 0.004% FS
-18 ± 0.05% rdg, ± 0.004% FS -3 ± 0.05% rdg, ± 0.004% FS
-12 ± 0.05% rdg, ± 0.004% FS -2 ± 0.05% rdg, ± 0.004% FS
-6 ± 0.05% rdg, ± 0.004% FS -1 ± 0.05% rdg, ± 0.004% FS
0 ± 0.05% rdg, ± 0.004% FS 0 ± 0.05% rdg, ± 0.004% FS
6 ± 0.05% rdg, ± 0.004% FS 1 ± 0.05% rdg, ± 0.004% FS
12 ± 0.05% rdg, ± 0.004% FS 2 ± 0.05% rdg, ± 0.004% FS
18 ± 0.05% rdg, ± 0.004% FS 3 ± 0.05% rdg, ± 0.004% FS
24 ± 0.05% rdg, ± 0.004% FS 4 ± 0.05% rdg, ± 0.004% FS
30 ± 0.05% rdg, ± 0.004% FS 5 ± 0.05% rdg, ± 0.004% FS
C ALI BR ATING V O LTAGE
R ANGE +/- 30 V
A pp ly no mi na l FS v a l ue
P r ess ENTE R k e y w h en
app li ed v a l ue i s stab l e
SET VALUE
C HANGE
VALUE
R UN
C ALI BR ATING V O LTAGE
R ANGE +/- 30 V
E nte r A pp li ed V a l ue:
C HANGE
VALUE
R UN
C ALI BR ATING V O LTAGE
R ANGE +/- 30 V
E nte r A pp li ed V a l ue:
C ALI BR ATING V O LTAGE
R ANGE +/- 30 V
St ore F S poin t ?
YES N O
C ALI BR ATING V O LTAGE
R ANGE +/- 30 V
R ESULTS
m = 1 . 395879e - 05
c = - 7 . 12800 4 e + 00
A pp li ed M easu r ed
0 . 0000 526380
29 . 98 4 873988
Ca li b r at i on Co m p l ete
P r ess ENTE R to cont i nue
Calibration