manualshive.com logo in svg

GE HEALTHCARE B20, User'S Reference Manual

Share
Download
GE HEALTHCARE B20 User'S Reference Manual Download Page 296

B40/B20 Patient Monitor

18-2

Overview

Entropy is a non-invasive parameter suitable for adults and pediatric patient population older 
than two years of age.
Entropy may be used as an aid in monitoring the effects of certain anesthetic agents on the 
patient’s central nervous system (CNS) during general anesthesia. Displaying and using clinical 
information from Response Entropy (RE) and State Entropy (SE) may allow the clinician to tailor 
the anesthetic according to the individual needs of a patient.
The use of Entropy parameters may help the clinician to improve drug management. It may 
also enable a faster recovery from anesthesia and a more predictable wake-up and 
extubation.
Prior to using Entropy as an adjunct to guide anesthesia care, it is recommended to review 
important situations and limitations that can influence the Entropy number. GE recommends 
that clinicians review the following practice advisory that includes a section on brain function 
monitoring: The American Society of Anesthesiologists, Practice Advisory for Intraoperative 
Awareness and Brain Function Monitoring (Anesthesiology 2006; 104: 847-64). Clinicians are 
also recommended to maintain current knowledge of government regulatory, practice or 
research information on brain function monitoring and related topics.
Entropy is for monitoring the state of CNS by data acquisition of electroencephalograph (EEG) 
and frontal electromyograph (FEMG) signals. The spectral entropies, Response Entropy (RE) and 
State Entropy (SE), are processed EEG and FEMG variables. The Entropy measurement is to be 
used as an adjunct to other physiological parameters.
Response Entropy (RE) and State Entropy (SE) may be used as an aid in monitoring the effects of 
certain anesthetic agents, which may help the user titrate anesthetic drugs according to the 
individual needs of patients. Furthermore, the use of Entropy parameters may be associated 
with a reduction of anesthetic use and faster emergence from anesthesia.
The Entropy module and accessories are indicated for use by qualified medical personnel only.

Figure 18-1 Entropy measurement connector

Entropy
connector

Summary of Contents for B20

































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands