Garmin GNS 530, Pilot'S Manual And Reference, Page: 72 / 282

GNS 530(A) Pilot’s Guide and Reference
190-00181-00 Rev. G
5-6
SECTION 5
FLIGHT PLANS
Flight Plan Catalog Options
/ iÊvœœÜˆ˜}ʜ«Ìˆœ˜ÃʭܓiÊVœÛiÀi`ʜ˜ÊÌ iÊ«ÀiVi`ˆ˜}Ê
«>}iîÊ>ÀiÊ>Û>ˆ>LiÊvœÀÊÌ iʏˆ} ÌÊ*>˜Ê>Ì>œ}Ê*>}i\
UÊ ¼V̈Û>Ìiʏˆ} ÌÊ*>˜¶½Ê‡ÊœÜÃÊÌ iÊ«ˆœÌÊ̜Ê
select the flight plan for navigation guidance, as
described previously in this section.
UÊ ¼˜ÛiÀÌÊEÊV̈Û>ÌiÊ*¶½Ê‡ÊœÜÃÊÌ iÊ«ˆœÌÊ̜Ê
reverse the highlighted flight plan and select it for
navigation guidance, as described previously in
this section.
UÊ ¼Ài>ÌiÊ iÜʏˆ} ÌÊ*>˜¶½Ê‡ÊœÜÃÊÌ iÊ«ˆœÌÊ̜Ê
create a new flight plan, as described previously in
this section.
UÊ ¼ÀœÃÃw¶½Ê‡ÊœÜÃÊÌ iÊ«ˆœÌÊ̜ÊÌÀ>˜ÃviÀÊ>ʈÀiV̜̇Ê
destination, the active flight plan, any stored flight
«>˜ÊœÀÊÕÃiÀÊÜ>Þ«œˆ˜ÌÃÊ̜Ê>ÊÃiVœ˜`Ê{ää‡-iÀˆiÃʜÀÊ
500-Series Garmin unit. Some crossfill operations
can be done automatically. If both units are set
̜ʼ>Õ̜½]Ê>ÊV >˜}iʈ˜ÊÌ iÊ`ˆÀiV̜̇Ê`iÃ̈˜>̈œ˜ÊœÀÊ
active flight plan on one unit is seen on the other.
œÀÊ>``ˆÌˆœ˜>Êˆ˜vœÀ“>̈œ˜]ÊÃiiÊ-iV̈œ˜Ê£ä°Ó]Ê
ˆ} ÌÊ*>˜˜ˆ˜}Ê*>}i\ÊÀœÃÃw°
Crossfilling flight plans between two 400-
or 500-Series Garmin units:
1) Select the ‘Crossfill?’ option from the Flight
Plan Catalog Page Menu (Figure 5-12) and
press the
ENT Key.
2) Turn the large right knob to select the
‘Method’ field (Figure 5-13).
3) Turn the small right knob to select ‘Auto’
or ‘Manual’ and press the ENT Key. ‘Auto’
automatically transfers the active flight plan
or Direct-to selection to another 400- or 500-
series Garmin unit, without user intervention.
4) If ‘Manual’ is selected: Turn the large
right
knob to select the ‘Transfer’ field, then turn
the small
right knob to select the type of
information to transfer between units (active
flight plan, flight plan, all user waypoints or
a single user waypoint). When ‘Flight Plan’
or ‘User Waypoint’ is selected, a second field
appears to the immediate right of the ‘Transfer’
field. Use the small and large
right knobs to
enter the number of the flight plan or the name
of the user waypoint to be transferred.
5) The ‘Cross-Side’ field allows the pilot to
designate the sending and receiving units
in a crossfill operation. Turn the large
right
knob to select the ‘Cross-side’ field, then turn
the small
right knob to select ‘To’ or ‘From’
(Figure 5-14). Press the ENT Key to confirm
the selection.
6) Turn the large right knob to highlight ‘Initiate
Transfer?’ (Figure 5-14) and press the ENT
Key. Once ‘Initiate Transfer?’ is selected,
a progress bar at the bottom of the page
indicates the status of the crossfill transfer until
completed.
Figure 5-14 Crossfill Page