Gako Unguator e/s Operating Instructions Manual Download Page 42

Page: 42 / 52

Notes on safety

Notes on safety

• UNGUATOR

devices must only be connected to grounding-type receptacles with

230 V or rated country-specific voltage installed according to the regulations of
DIN VDE 0100.

• UNGUATOR

devices have been designed for operation under normal room

atmospheric conditions. Recommended values: Ambient temperature 15...30 °C/
59...86 °F and relative air humidity less than 80 %.

• The device should be allowed to acclimatize for approx. 30 minutes at commissioning

and/or after extended storage time in cold rooms.

• UNGUATOR

devices should only be operated by authorized persons.

• UNGUATOR

power switch and power cord must be easily accessable.

• Do not immerse UNGUATOR

devices in water.

• Always pull the power plug before opening UNGUATOR

devices.

• Have electric parts removed or installed by professionals only.
• Only operate the UNGUATOR

MB with screwed-on UNGUATOR

Jar or in reaction

mixture glassware.

• Do not touch rotating parts.
• Keep long hair away from rotating parts.
• During the automatic lifting function of the UNGUATOR

2100: always keep long

hair, parts of the body or objects away from the lifting mechanism – immediately
turn off the power switch in an emergency or pull the power plug.

• Always keep the air vents on the driving head/back or underside of the

devices free when using the device.

• Using the UNGUATOR

devices not according to these operating

instructions or with line products that the manufacturer did not deliver or
recommend may impair safety.

• UNGUATOR

devices have not been designed for operation under

hazardous conditions. Heed the relevant safety regulations when handling hazardous
substances (e.g. combustible liquids such as alcohol or similar substances).

• UNGUATOR

devices correspond to the safety standards for laboratory

equipment. They have to be positioned to prevent any interference or use by
unauthorized persons.

• The device must not be disposed of in ordinary domestic waste.

Please deliver the device to the available collecting and recycling
systems at the end of its useful life.

Summary of Contents for Unguator e/s





















































Search results

Summary of Contents for Unguator e/s

Reviews:

Related manuals for Unguator e/s

Brands by name

Popular brands

Gako Unguator e/s, Operating Instructions Manual

Search results

Summary of Contents for Unguator e/s

Reviews:

Related manuals for Unguator e/s

Brands by name

Popular brands