manualshive.com logo in svg

Furuno FCV-38, Manual

Share
Download
Furuno FCV-38 Manual Download Page 80

3.  SCREENSHOTS & DATA RECORDING

3-8

4. Select the file to play back, then click [OK]. The selected file is played back. Some 

settings, such as gain and fish size measurements, can be adjusted during play-
back.

Note 1: 

To replay echo data from an external fish finder, set the mode to the one 

used to record the data, to ensure proper replay of data.

Note 2: 

Setting changes such as gain adjustment are not reflected in the echo 

data from an external fish finder.

5. Click the Stop icon (

) to stop the playback.

No.

Name

Description

1

[Pause] icon

Pauses the playback. Click the [Play] icon to continue play-
back.

2

[Stop] Icon

Stops the playback.

3

[Settings] icon

Applies your current settings to the playback file. This icon 
is shown in green color when in use.

4

[Loop] icon

Loops the playback.

5

[Playback Location] 
indicator

Indicates your current location in the overall playback. Se-
lect the slide bar, then drag the locater to change the play-
back location.

6

[Playback Speed]

Selects the speed to playback the record. The available 
options are:
•  [2000]/[1500]/[1000]/[500] ms: Play the record at the set 

millisecond speed.

•  [RT]: Play the record at real time speed (the speed at 

which it was recorded).

•  [MAX]: Play the record at maximum playback speed.

䐣

䐤

䐡

䐢

䐟

䐠

Summary of Contents for FCV-38

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands